Tools You Need to Set Up a New Bath Tub
Tools You Need to Set Up a New Bath Tub
Blog Article
This article listed below involving How to Install a Bathtub is immensely stimulating. You should check this stuff out.

Setting up a tub isn't precisely brain surgery, yet it does call for strong plumbing, woodworking, and also sometimes, tiling abilities. Changing an old bathtub with a new one is additionally a reasonably difficult task. If the old bathtub is easily available, the project can move speedily; if you need to open up a wall to remove the old bathtub as well as place the brand-new tub, the task is much harder. In either instance, the job is within a house handyman's skills, although you will certainly need a helper to vacate the old bathtub and set in the brand-new one. Ensure you have actually certified yourself for the job and also fit trying it. As opposed to employing a professional to take control of a halfway-completed project, it is far better to think about employing one prior to you start. Possibilities are you might need a professional plumber to make tube links.
This post will aid you set up a new tub in your restroom if you have actually already acquired a brand-new bathtub and also don't need to transform the setup of your previous water system pipelines.
Your devices and product list need to make up the following:
Planning for the Setup
To start with, the supporting frame provided with the bathroom ought to be fitted (if required) according to the manufacturer's directions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is essential to make sure that if the tap features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the faucets system to stop stress on the bath tub.
Fit the versatile faucet connectors to the bottom of the two faucets utilizing 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you make use of every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its final placement.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you must do is separate the water supply. After doing so, activate the taps to drain any type of water remaining in the system. The process of eliminating the existing taps can be rather problematic as a result of the limited gain access to that is frequently the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a cloth all set for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipes have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary faucets from transforming during this process. When the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Before carrying on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Bathtub
Utilizing both wood boards under its feet, place the tub in the called for position. The wooden boards are helpful in evenly spreading out the weight of the tub over the location of the boards instead of focusing all the weight onto 4 small points.
The following objective is to ensure that the tub is leveled all round. This can be accomplished by examining the spirit level and changing the feet on the tub till the level reads level.
To set up taps, fit all-time low of the outermost versatile tap port to the suitable supply pipe by making a compression join; then do the same for the various other faucet.
Activate the water supply and also check all joints and also brand-new pipework for leaks and tighten them if needed. Fill the bath tub as well as additionally examine the overflow outlet and the regular electrical outlet for leakages.
Finally, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bath tub ought to wait until the tub has been utilized at least when as this will resolve it right into its final placement.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will certainly need a plastic port to stop damages to the thread. One end of the port fits on the plastic tail of the faucet and the other end offers a connection to the current supply pipelines.
If you require to fit a monobloc, then you will need lowering couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin ensuring that the washers remain in area between the tap and also the sink. Secure the tap in position with the supplier offered backnut. As soon as the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with regular tap ports. The former type must be linked to the faucet ends first, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath satisfies the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to fracture an inflexible seal, triggering the water to permeate the wall surface in between the bathroom and also the tiling, causing issues with moisture as well as possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your components and also fittings. They are sold in tubes and also cartridges, as well as are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of drenched newspaper or soft rope. Remember to constantly load the tub with water before securing, to enable the motion experienced when the tub remains in usage. The sealant can crack rather very early if you do not take into consideration this movement prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise easily readily available on the market. It is advisable to fit the floor tiles using waterproof or water-proof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

I'm very involved in How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I really hope you liked the entire entry. Make sure you set aside a second to share this page if you appreciated it. Thank you for your time. Kindly stop by our blog back soon.
Book Service Now
Report this page